Quantum Scalar 1000 Uživatelská příručka Strana 42
- Strana / 122
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
34 The SAN Management Interface
When a SCSI channel is selected, the lower part of the data panel display presents the following
information:
When a Fibre Channel is selected, the lower part of the data panel display presents the following
information:
Serial Baud Rate Speed of the HyperTerminal connection
Health Check Level Level to which Health Check is set, 0-4
Health Check Interval Interval between Health Checks, in minutes
Receive Event Traps Status--either Enabled or Disabled
Ethernet Type 10-base T or 100-base T
UDP Port User Datagram Protocol port where SNMP traps are
received
VPS Enabled
SFM Enabled
Yes (enabled) or No (disabled)
VPM Enabled Yes (enabled) or No (disabled)
Data Mover Module Enabled Yes (enabled) or No (disabled)
Channel Type Low Voltage or High Voltage, Single-Ended or
Differential
Channel Mode Target or Initiator
Host ID (if channel in initiator mode) SCSI Bus Channel ID
Termination Status--either Enabled or Disabled
Max Width Bus width, in bits
Max Speed
Bus speed in megahertz
Status Status--either Operational or Offline
Max IDs per Bus (if channel in initiator mode) Number of SCSI IDs allowed
Max LUNs per ID (if channel in initiator mode) Number of SCSI LUNs allowed
World Wide Port Name Unique 64-bit identifier assigned to this port
World Wide Node Name Unique 64-bit identifier assigned by the manufacturer
Serial Number Number assigned to the FC connector during
manufacturing
Media Short Wave or Long Wave, Dual or Single PMC or GBIC
type
Firmware Revision FC controller firmware version
Port Type Point-to-Point (N_Port), fabric loop (NL_Port),
Fabric_Attached (N_Port), or none
Port Mode Public or Private, Initiator or Target
- User’s Guide 1
- 89558 Böhmenkirch 2
- Contents 3
- 6 Managing User Accounts 39 5
- 7 Working with Portals 43 5
- 11 Configuring SAN Access 75 6
- 12 Troubleshooting the SAN 93 6
- A Glossary 107 7
- Description 11
- Using the SAN Client 12
- Event Logging 12
- 6 Description 14
- 8 Description 16
- Getting Started 17
- Before Installing AMC 18
- Installing the AMC Server 19
- 12 Getting Started 20
- Launching the AMC Server 21
- Installing the AMC Client 22
- Launching the AMC Client 23
- Connecting to the Server 24
- Logging on 25
- Logging off 26
- Exiting the AMC Client 27
- Shutting Down the AMC Server 27
- 20 Getting Started 28
- Frequently Asked Questions 29
- 22 Frequently Asked Questions 30
- How do I create policies? 31
- 24 Frequently Asked Questions 32
- The SAN Management Interface 33
- Received Event Trap Window 34
- Scalar i2000 38
- Device Numbering 40
- Graphical Panel 40
- Data Panel 41
- Max Speed 42
- Status/Message Area 43
- Common SAN Management Options 44
- Managing User Accounts 47
- 40 Managing User Accounts 48
- Adding a New User Account 49
- Modifying a User Account 50
- Deleting a User Account 50
- Working with Portals 51
- Modifying a Portal 52
- Deleting a Portal 53
- 46 Working with Portals 54
- Working with SAN Categories 55
- Creating a new Category 56
- Renaming a Category 56
- Deleting a Category 56
- Moving a Category 57
- Moving Items by Drag and Drop 57
- Working With Views 59
- Opening Saved Views 60
- Creating Views 60
- Saving Views 62
- Deleting Views 62
- Searching the Current View 62
- Reporting the Current View 63
- Configuring Email 65
- Configuring Policies 66
- Discovering the SAN 67
- Rediscovering a Segment 68
- Managing the SAN Appliance 69
- Refreshing Data 70
- Updating Firmware 72
- Using Restart 72
- Displaying RMU Data 73
- Managing the SCSI Channel 75
- Configuring the SCSI Channel 76
- Managing the Fibre Channel 77
- Resetting the Fibre Channel 78
- Configuring the Fibre Channel 78
- Managing a Device 80
- Editing Device Maps 81
- Pre-Assigning Device Numbers 82
- Configuring SAN Access 83
- Using Channel Zoning 84
- Data Mover Module 84
- Installing HRS 85
- 78 Configuring SAN Access 86
- 80 Configuring SAN Access 88
- Installing SFM 89
- 82 Configuring SAN Access 90
- Adding SFM Hosts 91
- Using eVPS 92
- Installing eVPS 93
- 86 Configuring SAN Access 94
- 88 Configuring SAN Access 96
- Deleting eVPS Hosts 97
- Using the eVPS View Menu 97
- Using VPM 98
- Making VPM assignments 99
- 92 Configuring SAN Access 100
- Troubleshooting the SAN 101
- Interpreting the Event Log 102
- 96 Troubleshooting the SAN 104
- Receiving Event Traps 105
- Monitoring the LED Panel 106
- Figure 21 SNC 4000 LED panel 107
- Figure 22 SNC 5100 LED panel 107
- Using Identify 108
- Monitoring Environmental Data 109
- Using Health Check 110
- Obtaining a Drive Dump 111
- Checking the Command Flow Log 112
- 106 Troubleshooting the SAN 114
- Glossary 115
- 108 Glossary 116
- 110 Glossary 118
- 112 Index 120
- 114 Index 122
Související produkty a manuály pro Software Quantum Scalar 1000
Software Quantum DX30 Uživatelská příručka
(58 stránky)
(58 stránky)
Software Quantum SuperLoader 3 Uživatelská příručka
(160 stránky)
(160 stránky)
Software Quantum SuperLoader Uživatelská příručka
(196 stránky)
(196 stránky)
Software Quantum Scalar i2000 Uživatelská příručka
(544 stránky)
(544 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce