Quantum DLT 7000 Manuál Strana 30
- Strana / 312
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
- DLT™7000 Tape System 1
- Product Manual 1
- TABLE OF CONTENTS 7
- REVISION HISTORY 19
- Revision History 20
- Quantum DLT 7000 Tape System 20
- ABOUT THIS MANUAL 21
- CONVENTIONS 23
- FOR MORE INFORMATION… 23
- READER COMMENTS 24
- Chapter 1 25
- 1.2 PRODUCT FEATURES 26
- 1.3 PRODUCT SPECIFICATIONS 26
- 1.3.2 Interface Type 27
- 1.3.3 Storage Capacity 27
- 1.3.4 Reliability (Projected) 27
- 1.3.5 Performance Data 28
- 1.3.7 Power Requirements 32
- 1.3.8 Current Requirements 33
- 1.3.14 Conducted Emissions 36
- 1.3.15 Radiated Emissions 37
- 1.3.16 Susceptibility 37
- Chapter 2 39
- HARDWARE IMPLEMENTATION 39
- 2.1.1 Safety Precautions 40
- 2.1.2 Handling 40
- Hardware Implementation 43
- 4-Pin Power Connector 47
- Drive Back 47
- SCSI-2 Connector 47
- SCSI ID Pushbutton 51
- Power Switch 51
- Power Connector 51
- SCSI Connector (2) 51
- 220 / 240 V 53
- Table 2–6 LED Functionality 55
- 2.4.2 Selecting Density 59
- 2.5 POWER ON SELF TEST (POST) 61
- 2.6 TROUBLESHOOTING 63
- Chapter 3 65
- SCSI DESCRIPTION 65
- 3.2 SCSI COMMANDS 66
- SCSI Description 67
- 3.3 SIGNAL STATES 68
- 3.3.2 SCSI ID Bits 69
- 3.4 SCSI SIGNALS 70
- 3.4.2 Signal Bus Timing 71
- 3.5 SCSI BUS PHASES 74
- Messages Received by Drive: 75
- 3.5.2 ARBITRATION Phase 76
- 3.5.3 SELECTION Phase 77
- The initiator: 78
- The drive: 78
- 3.5.4 RESELECTION Phase 79
- 3.6 SCSI BUS CONDITIONS 88
- 3.6.2 Reset Condition 89
- 3.6.3 Queued Unit Attentions 90
- Chapter 4 91
- MESSAGES 91
- Messages 94
- 4.2 SUPPORTED SCSI MESSAGES 95
- 4.2.12 NO OPERATION (08h) 101
- • After a power cycle 103
- Chapter 5 105
- SCSI COMMANDS 105
- SCSI Commands 106
- 5.1.1 SCSI Pointers 107
- 5.1.3 Status/Error Reporting 110
- 5.2 SCSI COMMAND DESCRIPTIONS 116
- 5.3 ERASE COMMAND (19h) 118
- 5.4 INQUIRY COMMAND (12h) 119
- 5.6 LOCATE COMMAND (2Bh) 134
- 5.7 LOG SELECT COMMAND (4Ch) 136
- 5.7.2 Operation of LOG SELECT 138
- 5.8 LOG SENSE COMMAND (4Dh) 143
- • A page is not supported 146
- • The SP bit is set to 1 146
- • PPC bit set to 1 146
- (continued) 150
- 5.8.5 TapeAlert Page (2Eh) 154
- 0000h – 000Fh) 164
- 0000h, 0001h, or 0002h) 167
- 5.9.1 Mode Parameter List 171
- 5.9.8 TapeAlert Page (1Ch) 191
- 5.10.3 MODE SENSE Mode Pages 212
- 5.12 READ COMMAND (08h) 232
- READ Command (08h) 233
- 5.14.2 Data Mode 239
- 5.14.3 Descriptor Mode 240
- • A hard reset occurs 260
- 5.20 REWIND COMMAND (01h) 261
- 5.22 SPACE COMMAND (11h) 267
- 5.24 VERIFY COMMAND (13h) 270
- 5.25 WRITE COMMAND (0Ah) 272
- 5.26.2 Write Data Mode (010b) 275
- Appendix A 279
- INFORMATION 279
- Appendix B 283
- B.2 BUGCHECK PACKETS 284
- B.2.2 Event Log Packets 285
- Appendix C 287
- UPDATING THE FIRMWARE 287
- • Examines the data 289
- • Power failure 290
- Appendix D 293
- THE TAPE CARTRIDGE 293
- Reel Lock Opening 296
- Spring-Loaded Hub 297
- WRITE-PROTECTION 300
- D.4 LOADING A TAPE CARTRIDGE 302
- *81-60000-06 A01* 312
Související produkty a manuály pro Páskové jednotky Quantum DLT 7000
(12 stránky)
(300 stránky)
(1 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce