Quantum DLT 8000 Manuál Strana 200
- Strana / 408
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
SCSI Commands
5-56 Quantum DLT 8000 Tape System
LOG SENSE Command (4Dh) (continued)
5.8.5 TapeAlert Page (2Eh)
This page returns results of the tape drive’s on-going self diagnosis, so that the tape drive’s
behavior can be monitored and high reliability ensured. The TapeAlert page is read from the
tape drive at the beginning of each READ/WRITE activity, after any fatal errors occur during
a READ/WRITE, at the end of any tape cartridge when the READ/WRITE activity continues
onto another tape cartridge, and at the end of each READ/WRITE activity. The flags (Table
5–26) are set or cleared by the tape drive when the failure or corrective action occurs.
TAPE ALERT LOG PAGE HEADER
Bit
Byte
7 6 5 4 3 2 1 0
0 Page Code (2Eh)
1 Reserved
2 - 3
(MSB)
Page Length
(LSB)
Figure 5–24 TapeAlert LOG SENSE Header Format
Table 5–24 TapeAlert LOG SENSE Header Field Descriptions
Field Name Description
Page Code The Page Code echoes the page code that was specified in the LOG
SENSE command descriptor block.
Page Length The Page Length field specifies the total number of bytes contained in
this log page, not including the four bytes that make up the header.
- 8000 Tape System 1
- Product Manual 1
- Table of Contents 10
- REVISION HISTORY 27
- Revision History 28
- Quantum DLT 8000 Tape System 28
- ABOUT THIS MANUAL 33
- CONVENTIONS 35
- FOR MORE INFORMATION 35
- READER COMMENTS 35
- About This Manual 36
- Chapter 1 37
- 1.3 SPECIFICATIONS 38
- 1.3.4 Reliability (Projected) 41
- 1.3.5 Physical Specifications 41
- 1.3.7 Operating Air Velocity 43
- 1.3.9 Altitude 45
- 1.3.10 Acoustic Emissions 46
- 1.3.12 Power Requirements 47
- 1.3.13 Current Requirements 48
- TAPE SYSTEM 55
- 2.2.1 Setting the SCSI ID 58
- 2.2.2 Setting TERM PWR 60
- Front Bezel 61
- 2.3.1 Selecting SCSI ID 71
- SCSI Connectors (2) 72
- 220 / 240 V 74
- AC Power Cord Connector 75
- 2.4 The Tape Cartridge 76
- 2.4.4 Loading a Cartridge 82
- 2.4.5 Unloading a Cartridge 84
- 2.5.1 Unload Button 88
- 2.5.3 Selecting Density 89
- 2.9 Troubleshooting 99
- SCSI DESCRIPTION 103
- 3.2 SCSI Commands 104
- SCSI Description 105
- 3.3 Signal States 107
- 3.4 SCSI Signals 109
- 3.4.2 Signal Bus Timing 110
- 3.5 SCSI Bus Phases 113
- Bus Free Sequence 114
- 3.5.2 ARBITRATION Phase 115
- Arbitration Sequence 115
- 3.5.3 SELECTION Phase 116
- Selection Sequence 116
- Selection Time-Out 117
- 3.5.4 RESELECTION Phase 117
- Reselection Sequence 117
- SCSI ID bit 118
- Reselection Time-Out 120
- 3.6 SCSI Bus Conditions 128
- 3.6.2 Reset Condition 129
- 3.6.3 Queued Unit Attentions 130
- Chapter 4 131
- MESSAGES 131
- Messages 132
- 4.2 Supported SCSI Messages 135
- 4.2.12 NO OPERATION (08h) 141
- SCSI COMMANDS 145
- SCSI Commands 146
- 5.1.1 SCSI Pointers 147
- 5.1.3 Status/Error Reporting 151
- (Continued) 153
- 5.3 ERASE Command (19h) 159
- 5.4 INQUIRY Command (12h) 161
- 5.6 LOCATE Command (2Bh) 179
- 5.7 LOG SELECT Command (4Ch) 181
- Page Code Page Description 183
- 02h Write Error Counter Page 183
- 03h Read Error Counter Page 183
- 32h Compression Ratio Page 183
- LOG PAGE HEADER 184
- LOG PARAMETERS 185
- (continued) 186
- 5.8 LOG SENSE Command (4Dh) 189
- Descriptions (continued) 196
- 5.8.5 TapeAlert Page (2Eh) 200
- TAPE ALERT LOG PAGE HEADER 200
- TAPE ALERT LOG PARAMETERS 201
- Descriptions 210
- 5.9.1 Mode Parameter List 217
- 5.9.8 TAPEALERT PAGE (1Ch) 237
- FORCEDENSITY parameter to 4 247
- 5.10.3 MODE SENSE Mode Pages 258
- Data Field Description 284
- 5.14 READ Command (08h) 304
- 5.16.2 Data Mode 311
- 5.16.3 Descriptor Mode 311
- 5.26 REWIND Command (01h) 353
- 5.28 SPACE Command (11h) 360
- 5.30 VERIFY Command (13h) 363
- 5.31 WRITE Command (0Ah) 364
- 5.32.2 Write Data Mode (010b) 368
- INFORMATION 373
- Appendix B 377
- B.2 Bugcheck Packets 378
- B.2.1 POST Failure Packets 379
- B.2.2 Event Log Packets 379
- UPDATING THE FIRMWARE 381
- 1. POST passed 383
- 2. The drive is unloaded 383
- THE LIBRARY PORT 387
- CARTRIDGES 389
- Cartridge 391
- SYSTEM SCSI COMMANDS 397
- DLT 7000 EMULATION FEATURE 399
- SCSI Bus Differences 403
- Front Panel Differences 405
- *81-60118-04 A01* 408
Související produkty a manuály pro Páskové jednotky Quantum DLT 8000
Páskové jednotky Quantum LTO-6 Uživatelská příručka
(38 stránky)
(38 stránky)
Páskové jednotky Quantum DLT 2500 Servisní příručka
(114 stránky)
(114 stránky)
Páskové jednotky Quantum 3U Uživatelský manuál
(16 stránky)
(16 stránky)
Páskové jednotky Quantum LTO 4 Uživatelská příručka
(98 stránky)
(98 stránky)
Páskové jednotky Quantum DLT 7000 Manuál
(312 stránky)
(312 stránky)
Páskové jednotky Quantum DLT 2500 Manuál
(12 stránky)
(12 stránky)
Páskové jednotky Quantum DLT 4000 Manuál
(300 stránky)
(300 stránky)
Páskové jednotky Quantum LTO-2 Specifikace
(1 stránky)
(1 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce