Quantum Scalar 100 Uživatelská příručka Strana 101
- Strana / 126
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Troubleshooting and Help 12-91
Scalar 100
60 xx
Cannot complete the Lock/Unlock Mailbox commands.
Run Lock Diagnostics from the Operator Panel to see if there is any mechanical
bindings. Refer to Locking/Unlocking the Mailbox on page 8-63
.
Contact ATAC.
70 xx
Failures detected in the Picker Assembly Grip Finger Open operation.
Run Grip finger diagnostics. Refer to Exercising the Picker Fingers on page
9-67.
Contact ATAC.
71 xx
Failures detected in the Picker Assembly Grip Finger Close operation.
Run Grip finger diagnostics. Refer to Exercising the Picker Fingers on page
9-67.
Contact ATAC.
72 xx
A Get command was issued but the sensor indicated that a cartridge is
already present in the Picker Assembly.
Look into the Picker Assembly and see if a cartridge is present. If a cartridge is
found in the picker, recover the cartridge and place it in any empty slot, close
the door and retry the failing operation.
73 xx
Failures detected in the Picker Assembly Finger Open/Close operations.
Contact ATAC.
74 00
A Get command was issued but the sensor indicated that the source
location is empty.
This error can be caused by a cartridge that is not fully inserted in the storage
slot above the failing slot. If this condition exists, push the cartridge into its slot
and close the library door.
Contact ATAC.
77 xx
Failures detected in the Picker Assembly during a Retract operation.
Contact ATAC.
78 xx
A Put command was issued but the sensor indicated that the cartridge is
not present in the Picker Assembly.
Contact ATAC.
Reported
SAC
Error and Solution
- Scalar 100 1
- Copyright Notice 2
- Contents 3
- Using the Operator Panel 4
- Running your Library 5
- Configuring your Library 6
- Maintaining your Library 6
- Contents I-v 7
- Troubleshooting and Help 8
- Introduction 11
- Intended Audience 12
- Description 13
- Front Panel Components 14
- Front Power Switch 15
- Door Lock 15
- Operator Panel 15
- Back Panel Components 16
- Rear Power Switch 17
- Remote Management Unit 17
- Storage Networking Controller 17
- Internal Components 18
- Description 2-9 19
- SCSI Connections 20
- Setting up your Scalar 100 21
- Finding a Location 22
- Unpacking your Library 22
- Preparing the Host 24
- Host Coordinate System 25
- Installing a SCSI Adapter 25
- 3-16 6-00667-01 Rev B 26
- Rackmounting your Library 27
- Installing Side Panels 30
- Installing Casters 31
- Installing/Removing a Drive 31
- Removing a Drive 32
- Replacing a Drive 33
- Installing Bulk Load Mailbox 34
- Removing the Standard Mailbox 35
- Installing a Storage Column 38
- 4-30 6-00667-01 Rev B 40
- Working with Buttons 44
- Getting Library Messages 44
- Getting Mailbox Status 45
- Menu Guidelines 47
- Using the Main menu 47
- The Menu Tree 48
- Getting Information 49
- Getting Sensor Information 51
- Getting Slot Information 52
- Viewing Drive Information 55
- Getting Logs 55
- Printing Logs (HyperTerminal) 56
- Getting the Command Logs 56
- Getting Error Logs 57
- Getting Drive Logs 57
- Moving the Picker 60
- Taking Inventory 61
- CAUTION: 62
- Importing Tape Cartridges 63
- Exporting a Tape Cartridge 64
- Importing Cleaning Cartridges 65
- Working with Drives 66
- Configuring Barcode Length 69
- Configuring Drive Cleaning 70
- Setting Drive SCSI IDs 71
- Setting the Date and Time 71
- Locking/Unlocking the Mailbox 73
- 8-64 6-00667-01 Rev B 74
- Updating Drive Firmware 76
- Exercising the Picker Fingers 77
- Exercising the Picker Axes 79
- Exercising the Library 80
- Running a Demo 81
- Running a Self Test 81
- Resetting a Drive 82
- Servicing Drives 83
- 9-74 6-00667-01 Rev B 84
- Tape Use Guidelines 85
- Using Barcode Labels 86
- 10-78 6-00667-01 Rev B 88
- Starting the RMU 90
- Supported Browsers 90
- RMU Requirements 90
- Setting up the RMU 90
- Logging into the RMU 91
- Configuring SNMP 92
- Configuring RMU User Accounts 93
- Configuring the Time and Date 94
- Updating Firmware 94
- Viewing Diagnostic Files 95
- Viewing Logs 95
- Getting Help 96
- Operator Information Messages 110
- Interpreting Drive LEDs 111
- Getting More Information 111
- 12-102 6-00667-01 Rev B 112
- Specifications 113
- SDLT/DLT 114
- 13-106 6-00667-01 Rev B 116
- Regulatory Notices 117
- IC Notice (Canada Only) 118
- CE Notice 119
- VCCI Notices (Japan Only) 119
- Declaration of Conformity 120
- 15-112 6-00667-01 Rev B 122
- Index 15-113 123
- 15-114 6-00667-01 Rev B 124
- Index 15-115 125
Související produkty a manuály pro Páskové automatické zavaděče a knihovny Quantum Scalar 100
(16 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce