Quantum Scalar 100 Uživatelská příručka Strana 15
- Strana / 126
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Description 2-5
Scalar 100
Front Power Switch
There are two power switches on the library: the front power switch and the rear power switch.
Turning off the front power switch removes power from the internal electronics and removes power
from the drives, but the library still contains standby power. The standby power can only be turned
off by the rear power switch. See Rear Power Switch on page 2-7
.
Door Lock
The Scalar 100 door lock protects your data from the risk of tampering and prevents unauthorized
personnel from entering the mechanical area of the Scalar 100 where serious injury could occur.
When locked, the library door can only be opened from the outside with a key. Authorized personnel
are responsible for the security of the key. When shipped, the front door is locked. The key is
attached to the back panel of the library.
Mailbox
The Mailbox allows you to import and export tape cartridges without interrupting the normal
operation of the library; however, it can also be configured as additional storage slots.
There are two models of the Mailbox:
• The standard Mailbox has a capacity of one or two tape cartridges. (One tape cartridge for
DLT/SDLT and LTO libraries and two tape cartridges for AIT libraries.)
• The optional bulk load Mailbox enables you to load multiple tape cartridges at one time.
• AIT bulk load Mailboxes holds 16 tape cartridges in two magazines.
• LTO bulk load Mailboxes holds 12 tape cartridges in two magazines.
• DLT/SDLT bulk load Mailbox holds 10 tape cartridges in two magazines.
Operator Panel
The Operator Panel is an LCD screen that enables you to monitor, configure, and service your
library. For detailed information on the Operator Panel, see Using the Operator Panel on page 5-
31.
WARNING:
TO COMPLETELY REMOVE ALL POWER, EITHER USE THE REAR
POWER SWITCH OR DISCONNECT THE POWER CORD FROM THE
ELECTRICAL SOURCE.
WARNING:
THE MECHANICAL COMPONENTS OF THE LIBRARY CAN CAUSE
SERIOUS INJURY. ACCESS TO THE LIBRARY SHOULD BE
RESTRICTED TO AUTHORIZED PERSONNEL ONLY.
- Scalar 100 1
- Copyright Notice 2
- Contents 3
- Using the Operator Panel 4
- Running your Library 5
- Configuring your Library 6
- Maintaining your Library 6
- Contents I-v 7
- Troubleshooting and Help 8
- Introduction 11
- Intended Audience 12
- Description 13
- Front Panel Components 14
- Front Power Switch 15
- Door Lock 15
- Operator Panel 15
- Back Panel Components 16
- Rear Power Switch 17
- Remote Management Unit 17
- Storage Networking Controller 17
- Internal Components 18
- Description 2-9 19
- SCSI Connections 20
- Setting up your Scalar 100 21
- Finding a Location 22
- Unpacking your Library 22
- Preparing the Host 24
- Host Coordinate System 25
- Installing a SCSI Adapter 25
- 3-16 6-00667-01 Rev B 26
- Rackmounting your Library 27
- Installing Side Panels 30
- Installing Casters 31
- Installing/Removing a Drive 31
- Removing a Drive 32
- Replacing a Drive 33
- Installing Bulk Load Mailbox 34
- Removing the Standard Mailbox 35
- Installing a Storage Column 38
- 4-30 6-00667-01 Rev B 40
- Working with Buttons 44
- Getting Library Messages 44
- Getting Mailbox Status 45
- Menu Guidelines 47
- Using the Main menu 47
- The Menu Tree 48
- Getting Information 49
- Getting Sensor Information 51
- Getting Slot Information 52
- Viewing Drive Information 55
- Getting Logs 55
- Printing Logs (HyperTerminal) 56
- Getting the Command Logs 56
- Getting Error Logs 57
- Getting Drive Logs 57
- Moving the Picker 60
- Taking Inventory 61
- CAUTION: 62
- Importing Tape Cartridges 63
- Exporting a Tape Cartridge 64
- Importing Cleaning Cartridges 65
- Working with Drives 66
- Configuring Barcode Length 69
- Configuring Drive Cleaning 70
- Setting Drive SCSI IDs 71
- Setting the Date and Time 71
- Locking/Unlocking the Mailbox 73
- 8-64 6-00667-01 Rev B 74
- Updating Drive Firmware 76
- Exercising the Picker Fingers 77
- Exercising the Picker Axes 79
- Exercising the Library 80
- Running a Demo 81
- Running a Self Test 81
- Resetting a Drive 82
- Servicing Drives 83
- 9-74 6-00667-01 Rev B 84
- Tape Use Guidelines 85
- Using Barcode Labels 86
- 10-78 6-00667-01 Rev B 88
- Starting the RMU 90
- Supported Browsers 90
- RMU Requirements 90
- Setting up the RMU 90
- Logging into the RMU 91
- Configuring SNMP 92
- Configuring RMU User Accounts 93
- Configuring the Time and Date 94
- Updating Firmware 94
- Viewing Diagnostic Files 95
- Viewing Logs 95
- Getting Help 96
- Operator Information Messages 110
- Interpreting Drive LEDs 111
- Getting More Information 111
- 12-102 6-00667-01 Rev B 112
- Specifications 113
- SDLT/DLT 114
- 13-106 6-00667-01 Rev B 116
- Regulatory Notices 117
- IC Notice (Canada Only) 118
- CE Notice 119
- VCCI Notices (Japan Only) 119
- Declaration of Conformity 120
- 15-112 6-00667-01 Rev B 122
- Index 15-113 123
- 15-114 6-00667-01 Rev B 124
- Index 15-115 125
Související produkty a manuály pro Páskové automatické zavaděče a knihovny Quantum Scalar 100
(16 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.019 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce