Quantum Scalar 100 Uživatelská příručka Strana 67
- Strana / 126
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Configuring your Library 8-57
Scalar 100
Configuring your Library
You can configure your library in many different ways. Configuring includes setting the library SCSI
ID, setting the number of retries your library will attempt, and setting whether your Mailbox is to be
used for import/export functions or for storage. These operations are those that personalize the
library to your environment.
Configuring General Characteristics
The general characteristics of the library are configured using SCSI and Config. The following
sections describe how to use these commands.
Configuring Library Characteristics
Use SCSI to configure the general characteristics of your library. This includes the following items:
• Setting the SCSI ID of the library — Remember that it is important that each ID be unique
from other SCSI devices on the SCSI bus.
• Setting the number of retries — This the number of times the library will attempt to put or
get a media cartridge before it gives an error.
• Enabling or disabling Parity — This value defaults to enabled and must match the
configuration of the host bus adapter.
• Emulating a different library — You can configure your library to emulate other ADIC
products. This is useful if your host software recognizes other ADIC products, but not the
Scalar 100 (this may happen if, for example, you do not have the correct drivers installed).
This feature allows the Scalar 100 to appear like a different library so that the host knows
how to communicate with it.
Path: Main menu > More > Setup > Library > SCSI
To configure the library
1. From the Main menu, select More. Select Setup and then select Library. Select SCSI.
The current and new values display.
2. Use Up, Down, Next, and Yes/No to enter values in the following fields:
• SCSI ID — Sets the SCSI ID of the library. Available SCSI IDs are 0 to 7.
• Retries — Sets the number of retries. Possible values are 0 to 255.
• Parity — Enables or Disables parity. Possible values are Yes and No.
• Library sign-on — Changes the library sign-on. Possible values are Scalar 100, Scalar
DLT 448, Scalar 1000, and EXB-480.
NOTE:
Many other library characteristics are set using Config. For more information,
see Configuring General Characteristics on page 8-57
.
- Scalar 100 1
- Copyright Notice 2
- Contents 3
- Using the Operator Panel 4
- Running your Library 5
- Configuring your Library 6
- Maintaining your Library 6
- Contents I-v 7
- Troubleshooting and Help 8
- Introduction 11
- Intended Audience 12
- Description 13
- Front Panel Components 14
- Front Power Switch 15
- Door Lock 15
- Operator Panel 15
- Back Panel Components 16
- Rear Power Switch 17
- Remote Management Unit 17
- Storage Networking Controller 17
- Internal Components 18
- Description 2-9 19
- SCSI Connections 20
- Setting up your Scalar 100 21
- Finding a Location 22
- Unpacking your Library 22
- Preparing the Host 24
- Host Coordinate System 25
- Installing a SCSI Adapter 25
- 3-16 6-00667-01 Rev B 26
- Rackmounting your Library 27
- Installing Side Panels 30
- Installing Casters 31
- Installing/Removing a Drive 31
- Removing a Drive 32
- Replacing a Drive 33
- Installing Bulk Load Mailbox 34
- Removing the Standard Mailbox 35
- Installing a Storage Column 38
- 4-30 6-00667-01 Rev B 40
- Working with Buttons 44
- Getting Library Messages 44
- Getting Mailbox Status 45
- Menu Guidelines 47
- Using the Main menu 47
- The Menu Tree 48
- Getting Information 49
- Getting Sensor Information 51
- Getting Slot Information 52
- Viewing Drive Information 55
- Getting Logs 55
- Printing Logs (HyperTerminal) 56
- Getting the Command Logs 56
- Getting Error Logs 57
- Getting Drive Logs 57
- Moving the Picker 60
- Taking Inventory 61
- CAUTION: 62
- Importing Tape Cartridges 63
- Exporting a Tape Cartridge 64
- Importing Cleaning Cartridges 65
- Working with Drives 66
- Configuring Barcode Length 69
- Configuring Drive Cleaning 70
- Setting Drive SCSI IDs 71
- Setting the Date and Time 71
- Locking/Unlocking the Mailbox 73
- 8-64 6-00667-01 Rev B 74
- Updating Drive Firmware 76
- Exercising the Picker Fingers 77
- Exercising the Picker Axes 79
- Exercising the Library 80
- Running a Demo 81
- Running a Self Test 81
- Resetting a Drive 82
- Servicing Drives 83
- 9-74 6-00667-01 Rev B 84
- Tape Use Guidelines 85
- Using Barcode Labels 86
- 10-78 6-00667-01 Rev B 88
- Starting the RMU 90
- Supported Browsers 90
- RMU Requirements 90
- Setting up the RMU 90
- Logging into the RMU 91
- Configuring SNMP 92
- Configuring RMU User Accounts 93
- Configuring the Time and Date 94
- Updating Firmware 94
- Viewing Diagnostic Files 95
- Viewing Logs 95
- Getting Help 96
- Operator Information Messages 110
- Interpreting Drive LEDs 111
- Getting More Information 111
- 12-102 6-00667-01 Rev B 112
- Specifications 113
- SDLT/DLT 114
- 13-106 6-00667-01 Rev B 116
- Regulatory Notices 117
- IC Notice (Canada Only) 118
- CE Notice 119
- VCCI Notices (Japan Only) 119
- Declaration of Conformity 120
- 15-112 6-00667-01 Rev B 122
- Index 15-113 123
- 15-114 6-00667-01 Rev B 124
- Index 15-115 125
Související produkty a manuály pro Páskové automatické zavaděče a knihovny Quantum Scalar 100
(16 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.021 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce