Quantum Scalar 100 Uživatelská příručka Strana 34
- Strana / 130
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
26 Using the Optional Features
7 Remove the side covers. Looking at the rear of the library, unscrew the four Phillips screws that secure
each of the side covers (eight screws total). After removing the Phillips screws, open the front door and
slide the covers off the library.
8 Remove all drives and the DC power supplies from the library to reduce its weight. Each of these items
can be easily removed by loosening the captive thumbscrews and sliding the item out of the chassis.
9 Standing at the front of the rack, use the handles on both sides of the Scalar 100 to lift and position the
library onto the rackmount hardware.
10 Slide the library into the rack until it stops.
Installing Side Panels
Your library can be setup as a floor model or a rackmount library. Read the following instructions to configure
your library as a floor model unit, by installing side panels.
Tools required:
• Large flat blade screwdriver or 3/8 nut driver
• Phillips screwdriver
1 Verify that the Scalar 100 library is turned off using the main switch on the rear of the library. Turning
off power using only the front panel switch is not sufficient.
2 Fully open the front door of the library.
3 Install the side panel by capturing the vertical flange on the front of the library. The four holes on the
side panel should align with the four holes in the rear of the library.
4 Using a Phillips screwdriver, install the four thread-cutting screws contained in the Floor Model Kit.
5 Repeat steps 1 through 4 to install the other side panel.
6 Close the front door of the library.
7 If you are installing casters on this library, refer to Installing Casters on page 27. Otherwise, move the
library to its permanent location.
If the Scalar 100 is installed on a raised floor with forced air below, ensure that a floor cutout is beneath
the library.
WARNING
EVEN WITH THE ABOVE COMPONENTS REMOVED, THE SCALAR
100 WEIGHS IN EXCESS OF 150 LBS (65 KGS) AND REQUIRES
TWO PERSONS TO PROPERLY LIFT AND POSITION IT IN A
RACK.
Note
Both side panels are identical and can be installed on either side of the
library.
- 100 User’s Guide 1
- Contents 3
- 5 Using the Operator Panel 37 4
- 6 Getting Information 47 4
- 7 Running your Library 59 5
- 8 Configuring your Library 67 5
- 9 Maintaining your Library 75 5
- 13 Specifications 111 7
- Product Safety Statements 9
- Product Model Number 9
- Description 11
- Front Panel Components 12
- Back Panel Components 13
- 6 Description 14
- Rear Power Switch 15
- Internal Components 16
- Tape Magazines 17
- Slot Numbering 17
- Drive Module Numbering 18
- Host Attachment 19
- 12 Description 20
- Setting up your Scalar 100 21
- Finding a Location 22
- Unpacking your Library 22
- Scalar 100 User’s Guide 15 23
- 16 Setting up your Scalar 100 24
- Scalar 100 User’s Guide 17 25
- Preparing the Host 26
- Host Coordinate System 27
- Installing a SCSI Adapter 27
- Installing Drivers 27
- 20 Setting up your Scalar 100 28
- Scalar 100 User’s Guide 21 29
- 22 Setting up your Scalar 100 30
- Using the Optional Features 31
- Scalar 100 User’s Guide 25 33
- Installing Side Panels 34
- Installing Casters 35
- Installing/Removing Drives 35
- Removing a Drive 36
- Replacing a Drive 37
- Installing Bulk Load Mailbox 38
- Removing the Standard Mailbox 39
- Installing a Storage Column 41
- Partitioning Your Library 42
- Configuring AutoCleaning 42
- Working with AutoClean 43
- Using the Operator Panel 45
- 38 Using the Operator Panel 46
- Scalar 100 User’s Guide 39 47
- 40 Using the Operator Panel 48
- Working with Buttons 49
- Getting Library Messages 49
- Getting Mailbox Status 49
- 42 Using the Operator Panel 50
- Menu Guidelines 51
- Using the Main Menu 52
- The Menu Tree 52
- Scalar 100 User’s Guide 45 53
- 46 Using the Operator Panel 54
- Getting Information 55
- 48 Getting Information 56
- Getting Sensor Information 57
- Getting Slot Information 58
- Scalar 100 User’s Guide 51 59
- Viewing Drive Information 60
- Getting Logs 61
- Getting the Command Logs 62
- Getting Error Logs 62
- Getting Drive Logs 62
- Clear Log 63
- Force Dump 63
- Copy Dump 64
- Preserve Dump Dialog 64
- Scalar 100 User’s Guide 57 65
- 58 Getting Information 66
- Running your Library 67
- Moving Tape Cartridges 68
- Moving the Picker 69
- Taking Inventory 69
- 62 Running your Library 70
- Importing Tape Cartridges 71
- Exporting a Tape Cartridge 71
- 64 Running your Library 72
- Working with Drives 73
- Unloading a Drive 74
- Configuring your Library 75
- 68 Configuring your Library 76
- Scalar 100 User’s Guide 69 77
- Configuring Barcode Length 78
- Setting Drive SCSI IDs 79
- Setting Drive Loop IDs 80
- Setting the Date and Time 80
- Locking/Unlocking the Mailbox 81
- 74 Configuring your Library 82
- Maintaining your Library 83
- Updating Drive Firmware 84
- Exercising the Picker Fingers 85
- 78 Maintaining your Library 86
- Exercising the Picker Axes 87
- Exercising the Library 88
- Running a Self Test 89
- Teaching the Library 89
- Resetting a Drive 90
- Servicing Drives 90
- Scalar 100 User’s Guide 83 91
- 84 Maintaining your Library 92
- Tape Use Guidelines 93
- Using Barcode Labels 94
- Scalar 100 User’s Guide 87 95
- Scalar 100 User’s Guide 89 97
- Supported Browsers 98
- RMU Requirements 98
- Setting up the RMU 98
- Starting the RMU 99
- Logging into the RMU 99
- Configuring SNMP 100
- Configuring RMU User Accounts 100
- Configuring the Time and Date 101
- Updating Firmware 102
- Viewing Diagnostic Files 102
- Viewing Logs 103
- Getting Help 103
- Replacing the RMU 103
- Troubleshooting and Help 105
- 98 Troubleshooting and Help 106
- Scalar 100 User’s Guide 99 107
- 100 Troubleshooting and Help 108
- Scalar 100 User’s Guide 101 109
- 102 Troubleshooting and Help 110
- Scalar 100 User’s Guide 103 111
- 104 Troubleshooting and Help 112
- Scalar 100 User’s Guide 105 113
- 106 Troubleshooting and Help 114
- Scalar 100 User’s Guide 107 115
- 108 Troubleshooting and Help 116
- Operator Information Messages 117
- Interpreting Drive LEDs 118
- Specifications 119
- Tape Cartridge Capacity 120
- Drive Capacity 120
- Scalar 100 User’s Guide 113 121
- SDLT/DLT 122
- Scalar 100 User’s Guide 115 123
- 116 Specifications 124
- Scalar 100 User’s Guide 117 125
- 118 Index 126
- Scalar 100 User’s Guide 119 127
- 120 Index 128
- Scalar 100 User’s Guide 121 129
- 122 Index 130
Související produkty a manuály pro Páskové automatické zavaděče a knihovny Quantum Scalar 100
(168 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.076 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce