Quantum Scalar 100 Uživatelská příručka Strana 42
- Strana / 130
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
34 Using the Optional Features
2 Open the library front door. If necessary, move the picker assembly up the Y-axis to allow room. Slide
the storage column in place.
3 Perform one of the following two steps depending on the column you are installing:
• If you are installing column 4, use the T20 Torx wrench to tighten the two bottom hex screws
that attach the storage column to the bottom chassis.
• If you are installing column 5, use the 7/16 nut driver to tighten the bolt that attach the storage
column to the bracket.
4 Install the top bolt using the 7/16 nut driver.
5 Place the magazines in the storage column.
Partitioning Your Library
In Drive Control Path libraries, you can divide the drives and storage slots into up to three partitions.
Partitioning the library allows the server to run different applications in each partition and mixing LTO drives
within your library. You can install different generations of LTO drives in your library; however, the drive
types cannot be mixed within the same partition. Partitions cannot share drives or storage slots. An
exception to the sharing restrictions are cleaning tapes, which can be shared among all partitions.
Path: Main Menu > More > Setup > Library > Partitions
1 From the main menu, select More and then select Setup and then select Library. Select Partition.
2 The number of partitions appears on the panel.
3 To change the quantity of partitions, press Next until the quantity of partitions that you want displays.
Press OK.
4 Reboot the library to activate the changes.
Control Path
Control paths are logical paths into the library through which a server sends SCSI command to control the
actions of the partition. Additional control paths reduce the likelihood of a the entire library to fail if one
partition should go down.
Configuring AutoCleaning
In most configurations, drive cleaning is controlled through the host; however, if desired, the library has an
AutoClean feature that enables the library to control drive cleaning. (Host controlled drive cleaning is the
default condition.)
Drive cleaning requires cleaning cartridges to be imported into the library. (Note that cleaning cartridges are
imported differently than regular tape cartridges.) A total of three cleaning cartridges can be imported. These
cartridges are stored in fixed slots located at the top of columns 2, 4, and 5. These slots are not counted as
part of the slot capacity of the library, are not included in the report of storage elements, and are not
addressable to SCSI hosts.
Note
You can enable the partitioning feature after drives are installed and the control
path feature is enabled.
Note
A DLT cleaning tape cannot be used in an SDLT drive.
- 100 User’s Guide 1
- Contents 3
- 5 Using the Operator Panel 37 4
- 6 Getting Information 47 4
- 7 Running your Library 59 5
- 8 Configuring your Library 67 5
- 9 Maintaining your Library 75 5
- 13 Specifications 111 7
- Product Safety Statements 9
- Product Model Number 9
- Description 11
- Front Panel Components 12
- Back Panel Components 13
- 6 Description 14
- Rear Power Switch 15
- Internal Components 16
- Tape Magazines 17
- Slot Numbering 17
- Drive Module Numbering 18
- Host Attachment 19
- 12 Description 20
- Setting up your Scalar 100 21
- Finding a Location 22
- Unpacking your Library 22
- Scalar 100 User’s Guide 15 23
- 16 Setting up your Scalar 100 24
- Scalar 100 User’s Guide 17 25
- Preparing the Host 26
- Host Coordinate System 27
- Installing a SCSI Adapter 27
- Installing Drivers 27
- 20 Setting up your Scalar 100 28
- Scalar 100 User’s Guide 21 29
- 22 Setting up your Scalar 100 30
- Using the Optional Features 31
- Scalar 100 User’s Guide 25 33
- Installing Side Panels 34
- Installing Casters 35
- Installing/Removing Drives 35
- Removing a Drive 36
- Replacing a Drive 37
- Installing Bulk Load Mailbox 38
- Removing the Standard Mailbox 39
- Installing a Storage Column 41
- Partitioning Your Library 42
- Configuring AutoCleaning 42
- Working with AutoClean 43
- Using the Operator Panel 45
- 38 Using the Operator Panel 46
- Scalar 100 User’s Guide 39 47
- 40 Using the Operator Panel 48
- Working with Buttons 49
- Getting Library Messages 49
- Getting Mailbox Status 49
- 42 Using the Operator Panel 50
- Menu Guidelines 51
- Using the Main Menu 52
- The Menu Tree 52
- Scalar 100 User’s Guide 45 53
- 46 Using the Operator Panel 54
- Getting Information 55
- 48 Getting Information 56
- Getting Sensor Information 57
- Getting Slot Information 58
- Scalar 100 User’s Guide 51 59
- Viewing Drive Information 60
- Getting Logs 61
- Getting the Command Logs 62
- Getting Error Logs 62
- Getting Drive Logs 62
- Clear Log 63
- Force Dump 63
- Copy Dump 64
- Preserve Dump Dialog 64
- Scalar 100 User’s Guide 57 65
- 58 Getting Information 66
- Running your Library 67
- Moving Tape Cartridges 68
- Moving the Picker 69
- Taking Inventory 69
- 62 Running your Library 70
- Importing Tape Cartridges 71
- Exporting a Tape Cartridge 71
- 64 Running your Library 72
- Working with Drives 73
- Unloading a Drive 74
- Configuring your Library 75
- 68 Configuring your Library 76
- Scalar 100 User’s Guide 69 77
- Configuring Barcode Length 78
- Setting Drive SCSI IDs 79
- Setting Drive Loop IDs 80
- Setting the Date and Time 80
- Locking/Unlocking the Mailbox 81
- 74 Configuring your Library 82
- Maintaining your Library 83
- Updating Drive Firmware 84
- Exercising the Picker Fingers 85
- 78 Maintaining your Library 86
- Exercising the Picker Axes 87
- Exercising the Library 88
- Running a Self Test 89
- Teaching the Library 89
- Resetting a Drive 90
- Servicing Drives 90
- Scalar 100 User’s Guide 83 91
- 84 Maintaining your Library 92
- Tape Use Guidelines 93
- Using Barcode Labels 94
- Scalar 100 User’s Guide 87 95
- Scalar 100 User’s Guide 89 97
- Supported Browsers 98
- RMU Requirements 98
- Setting up the RMU 98
- Starting the RMU 99
- Logging into the RMU 99
- Configuring SNMP 100
- Configuring RMU User Accounts 100
- Configuring the Time and Date 101
- Updating Firmware 102
- Viewing Diagnostic Files 102
- Viewing Logs 103
- Getting Help 103
- Replacing the RMU 103
- Troubleshooting and Help 105
- 98 Troubleshooting and Help 106
- Scalar 100 User’s Guide 99 107
- 100 Troubleshooting and Help 108
- Scalar 100 User’s Guide 101 109
- 102 Troubleshooting and Help 110
- Scalar 100 User’s Guide 103 111
- 104 Troubleshooting and Help 112
- Scalar 100 User’s Guide 105 113
- 106 Troubleshooting and Help 114
- Scalar 100 User’s Guide 107 115
- 108 Troubleshooting and Help 116
- Operator Information Messages 117
- Interpreting Drive LEDs 118
- Specifications 119
- Tape Cartridge Capacity 120
- Drive Capacity 120
- Scalar 100 User’s Guide 113 121
- SDLT/DLT 122
- Scalar 100 User’s Guide 115 123
- 116 Specifications 124
- Scalar 100 User’s Guide 117 125
- 118 Index 126
- Scalar 100 User’s Guide 119 127
- 120 Index 128
- Scalar 100 User’s Guide 121 129
- 122 Index 130
Související produkty a manuály pro Páskové automatické zavaděče a knihovny Quantum Scalar 100
(168 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce